Numerology Store    Download  Video    Forum


Go Back   Five12.net -- Online Forum for the Numerology Music Sequencer > Numerology > Feature Requests

Reply
 
Thread Tools Display Modes
  #1  
Old 03-16-2009, 02:42 AM
jue's Avatar
jue jue is offline
Numerologist
 
Join Date: Nov 2008
Location: european outback
Posts: 650
Default new SendOut module

Hello,

with the upcomming Loop Bar there should be a new module that sends out events at a given beat / bar / time.

Just with the possibility to select a timepoint, lets say 67 : 3 when reaching this point the module sends out a CV value, a gate and a trigger.
With two sliders for CV value and the lenght of the gate.
Outputs are CV out, Gate out and Trigger out.
With this it should be possible to create special events in the timing of your sequences.
Examples:
Setting Keyswitches at the beginning of your sequence for samplers.
Sending out transpositions at given times.
Sending out programchanges at given times.
Start sequencers at given times for single runs, no more need to look for other possibilies to mute your running seqs as some kind of arrangement.
Shifting the steps of seqs at given times.
and so on.....

best
jue
__________________
Reply With Quote
  #2  
Old 03-17-2009, 11:23 AM
jim jim is offline
Administrator
 
Join Date: Nov 2008
Location: Albuquerque, NM
Posts: 4,574
Default

I'll think about that one. In the meanwhile, you can simulate most of that with a GateSeq, of course...

Cheers,
Jim
Reply With Quote
  #3  
Old 03-17-2009, 12:29 PM
jue's Avatar
jue jue is offline
Numerologist
 
Join Date: Nov 2008
Location: european outback
Posts: 650
Default

Hello,

that works well when our composition is not so long, 10 minutes or so.
The works I am doing normally are between 60 to 75 minutes and this is a little difficult to get with the GateSeqs.
Thats also a point because I was asking about a bigger CV switch to handle more 128 step GateSeqs.

best
jue
__________________
Reply With Quote
  #4  
Old 03-18-2009, 06:39 PM
lut lei's Avatar
lut lei lut lei is offline
Senior Member
 
Join Date: Nov 2008
Posts: 102
Default

Why don't you use the timeline for this, jue? Just curious. It seems to be a valid tool. Although I would like to see a module like this, sending out a set of values, when it receive a chosen value. (be it measure in time or a CV).
Reply With Quote
  #5  
Old 03-19-2009, 12:25 AM
jue's Avatar
jue jue is offline
Numerologist
 
Join Date: Nov 2008
Location: european outback
Posts: 650
Default

Hello,

with the timeline everything is static only the time changes.
With a modul like this you can change what should been send out at this given timepoint. Meaning generating the values along with your sequences and send them then out at this fixed time. In the timeline you have presets to set up and send them out, this means you have to know which values you want, but I do not know them in advance because I generate them over time.
It should work some how similar to the hardsync for me.

best
jue
__________________
Reply With Quote
  #6  
Old 03-19-2009, 04:45 PM
jim jim is offline
Administrator
 
Join Date: Nov 2008
Location: Albuquerque, NM
Posts: 4,574
Default

What is the longest cycle time (in beats) that you would need? I'm thinking that perhaps you might be able to do it with a very slow-running, long GateSeq triggering another sequencer. If you use the "percent" rate mode, you can set a seq to run as slowly as one step every 90 beats (set the percentage to 9000). You could also set the trigger seq to run off a secondary clock set for a very low tempo....

Jim
Reply With Quote
  #7  
Old 03-19-2009, 04:56 PM
jue's Avatar
jue jue is offline
Numerologist
 
Join Date: Nov 2008
Location: european outback
Posts: 650
Default

hello,

have to check this!
Thank you!

best
jue
__________________
Reply With Quote
  #8  
Old 03-20-2009, 05:09 PM
jue's Avatar
jue jue is offline
Numerologist
 
Join Date: Nov 2008
Location: european outback
Posts: 650
Default

Hello,

the best solution for my problem could be the new step on trigger mode for the GateSeqs. Then I could use the GateSeqs as a kind of divider and could reach any time point that I like.

best
jue
__________________
Reply With Quote
  #9  
Old 03-20-2009, 06:57 PM
lut lei's Avatar
lut lei lut lei is offline
Senior Member
 
Join Date: Nov 2008
Posts: 102
Default

You could try this plugin I have for sending OSC-messages at specific times. I modified it a bit for making a cv and a gate, via audio, cause I like this idea of yours. Here's a screenshot:. Sorry for spamming, if you don't find this appropriate.
Reply With Quote
  #10  
Old 03-21-2009, 12:41 AM
jue's Avatar
jue jue is offline
Numerologist
 
Join Date: Nov 2008
Location: european outback
Posts: 650
Default

Hello,

also this plugin does not work for me, sorry!
As your other plugs they only show a blank module without any edit button.
I checked the deavl plug in your example and they work so there must be something that I do not have on my mac or there could be a spezial folder structure that I do not have.

BTW: How do you make this VST plugs? Because in the moment I am looking for it in MAX but could not find it.

best
jue
__________________
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 07:02 PM.


Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.